6 results Searching for ASTM D, NSF CPVC Pipe Fittings? Grainger’s got your back. Easy ordering & convenient delivery. Log-in or register for your. ASTM D / DM – 09be1 Standard Specification for. Chlorinated Poly( Vinyl Chloride) (CPVC) Plastic Hot- and. Cold-Water Distribution Systems. Buy ASTM D/DM Standard Specification for Chlorinated Poly(Vinyl Chloride) (CPVC) Plastic Hot- and Cold-Water Distribution Systems from SAI.

Author: Aragar Kagazilkree
Country: Reunion
Language: English (Spanish)
Genre: Environment
Published (Last): 13 December 2014
Pages: 30
PDF File Size: 11.87 Mb
ePub File Size: 7.19 Mb
ISBN: 177-1-28738-473-8
Downloads: 19266
Price: Free* [*Free Regsitration Required]
Uploader: Nezragore

Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard. Link to Active This link will always route to the current Active version of the standard.

Work Item s – proposed revisions of this standard. The products covered by this specification are intended for use with the distribution of pressurized liquids only, which are chemically compatible with the piping materials. Due to inherent hazards associated with testing components and systems with compressed air or other compressed gases d284 manufacturers do not allow pneumatic testing of their products.

The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other.

These components comprise pipe and tubing, socket-type fittings, street fittings, plastic-to-metal transition fittings, solvent cements, and adhesives. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date.


These notes and footnotes excluding those in tables and figures shall not be considered as requirements of the specification.

The components are intended for use in residential and commercial, hot and cold, potable water distribution systems. Historical Version s – view previous versions of standard. CPVC pipe, tubing, and fittings shall be classified by a single standard dimension ratio which shall be SDR 11, by a certain maximum continuous use temperature and qstm a certain diameter range for nominal pipe or tubing. Suggested hydrostatic design stresses and hydrostatic pressure ratings for pipe, tubing, and fittings are listed in Appendix X1.

The components covered by this specification are intended for use in residential and commercial, hot and cold, potable water distribution systems.

Pressurized compressed air or other compressed gases contain large amounts of stored energy which present serious saftey hazards should a system fail for any reason.

Design and qstm considerations are discussed in Appendix X2. This specification covers requirements, test methods, and methods of marking for chlorinated poly vinyl chloride plastic hot- and cold-water distribution system components made in one standard dimension ratio and intended for water service up to a certain temperature.


Requirements and methods of test are included for materials, workmanship, dimensions and tolerances, hydrostatic sustained pressure strength, and thermocycling resistance.

CPVC plastic-to-metal transition fittings intended for use up a certain temperature are classified on the basis of resistance to failure by thermocycling. This standard does not purport to address all of the safety concerns, if any, associated with its use.

These short-term properties include mechanical strength, heat resistance, flammability, and chemical resistance which shall be determined after performing different tests. The chlorinated poly vinyl chloride plastics are categorized by two criteria: A test shall also be conducted in order to determine the long-term hydrostatic strength of CPVC 41 pipe, tubing, and fittings.

An optional performance qualification and an in-plant quality control program are recommended in Appendix X3. wstm

Combining values from the two systems may result in non-conformance with the standard. It is d284 only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application.

This abstract is a brief summary of the referenced standard.