Heat line C24 Pdf User Manuals. View online or download Heat line C24 Installation, Servicing And User Instructions Manual. The boiler’s ‘Log Book’ must be completed at each Service visit. By means of a manual switch the C24/C28 can be set to operate in one of two operating modes, . Boiler Manuals for the Heatline Compact C24 appliance.
|Published (Last):||13 October 2007|
|PDF File Size:||13.29 Mb|
|ePub File Size:||4.79 Mb|
|Price:||Free* [*Free Regsitration Required]|
Remove the pump body from the hydraulic assembly heatline c24 manual releasing the clip The CH temperature sensor located on the return pipe should now be removed 7. No water in the installation: Verify the igniter unit.
Heat Line C24 Manuals
Verify the operation of the gas valve. Whenever the pressure shown on the gauge is higher then 1.
Verify the sensor F20 Overheating fault Verify the operation of the heatline c24 manual. Re-assemble the boiler in reverse order 7. Flow heating temperature sensor fault. Put in the new sensor. Open the isolating valves on the low and return connections. Replace low water pressure switch. Remove the boiler casing following the steps below 1. Make sure that all used washers are replaced if necessary. Fit the leads and replacement the heatline c24 manual 8. Fault in gas valve motor.
Heatline c24 manual download
Verify that the sensor is connected to the main board and the shunt is removed. To correctly fill in the water into the system you should follow the manuxl below:.
Re-assemble in reverse order Domestic hot water sensor replacement heatline c24 manual. Boiler heatline c24 manual Each Heatline boiler is equipped with following additional parts: All usable parts like washers, igniters etc will be replaced. Replace the burner bar and re-fit the burner blades 6.
On opening a hot water outlet the boiler automatically responds to fire the boiler and supply the water-to-water heat exchanger with hot water via the three port valve. Re-assemble the boiler in reverse order Pump replacement 1. Remove the clop on the heatlind body and then release the pipe of the expansion vessel as shown on the picture below.
Is the central heating? Boiler normal heatline c24 manual Your appliance can be set to work either on domestic hot water and heating or domestic hot water only. During heatline c24 manual yearly service Gas Safe Registered engineer or Heatline boiler specialist will check and clean your appliance as necessary.
Verify the gas valve connections. Yes Replace gas supply, pressure or gas valve No hot heatline c24 manual and no central heating Open a hot tap to create a demand — is there a spark at the ignition electrode?
Troubleshooting Manual |
Fault in the main board. Water pressure of the installation. Verify the operation of the condensate pump. Mmanual the motor 4. Check heatline c24 manual soundness and correct boiler operation.
Gain General Access -remove outer case front panel 3. Naturally in instances where you appliance is installed in a compartment we recommend that your compartment is ventilated for boiler cooling purposes.
Heatline c24 manual the electrical leads from the fan 4. Replace the heat exchanger F77 Fault manusl gas valve motor Verify the gas valve heatline c24 manual. Reset the appliance F68 Fluctuation of flame signal Verify the return gas circuit gas valve open.
To correctly fill in the water into the system you should follow the steps below: Isolate the appliance and switch off the electricity 2. Verify the state of the electrode. Remove the pump body from the hydraulic assembly by releasing the clip. Those appliances are not suitable for external installation unless protected by a purpose made c2 such as a boiler house.
Domestic hot heatline c24 manual mode On opening a hot water outlet the boiler automatically responds to fire the boiler and supply the water-to-water heat exchanger with hot water via the three port valve.
When the demand for central heating is fulfilled, the burner will shut down and the appliance will come to stand-by mode, until the heatline c24 manual hot water or heating demand. Fit the new heat exchanger checking that the plate numbers are the same.
Primary pressure sensor- it is hydraulically operated sensor that checks and monitors water shortage and water general pressure in the heat,ine circuit. Verify the sensor F76 Thermal fuse fault Verify the fuses connections.
Disconnect the electrical connections to gas valve modulating heatline c24 manual 5. Release the connection from gas valve and manifold inlet, retaining the washers for use on reassembly heatline c24 manual shown on the picture below. Refit in reverse order to removal, the polarity of the wires to the modulating coil is not important, replace any damaged washers as required No hot water and no central heating.