ISO. Second edition. Reference number Permission can be requested from either ISO at the address below or ISO’s member body in the. 31 Jul Purchase your copy of BS EN ISO as a PDF download or hard copy directly from the official BSI Shop. All BSI British Standards. EN ISO Intravascular catheters – Sterile and single-use catheters – Part 5 : Over-needle peripheral catheters – ISO specifies requirements.
|Published (Last):||12 June 2013|
|PDF File Size:||9.73 Mb|
|ePub File Size:||1.24 Mb|
|Price:||Free* [*Free Regsitration Required]|
I Principle Water is allowed to flow through the catheter and the amount of flow is measured either volumetrically or gravimetrically.
Standards are also reviewed periodically; a standard alongwith amendments is reaffirmed when such review indicates that no changes are needed; if the review indicates that changes are needed, it is taken up for revision.
Review of Indian Standards Amendments are issued to standards as the need arises on the basis of comments.
Copyright BIS has the copyright iso 10555-5 all its publications. Details of which is given in National Annex A. The corresponding Indian Standards iso 10555-5 are to be substituted in their places are iso 10555-5 below along with their degree of equivalence for the editions indicated: 01555-5 3 The point should be designed to be noncoring.
E-5 Test report The test report shall contain iso 10555-5 least the following information: The fluid pathway in the needle sio be free of unintended obstructions that would prevent flashback. Annex D shows examples of typical needle point geom- etries.
This does not preclude the free use, in the course of implementing the standard, iso 10555-5 necessary details, such as symbols and sizes, type or grade designations. Fixed or removable fitting per- mitting venting of air while restricting or preferably preventing the escape of blood.
BS EN ISO 10555-5:2013
An example of a suitable apparatus is shown in fig- ure B. All standards are subject to revision, and parties to agreements based iso 10555-5 this part of ISO are encouraged iso 10555-5 investigate the possibility of applying 10555–5 most recent editions of the standards indicated below.
If a steel tube is used, it shall connply with ISO Figure 1 — Typical over-needle peripheral intravascular catheter NOTE 2 At the time of publication 1055-55 this part of ISOthere is no acceptable, validated test method to determine radio-detectability. When iso 10555-5 needle is fully inserted into the catheter unit, the catheter tube shall iso 10555-5 extend beyond the heel of the needle bevel nor be nnore than 1 nnnn fronn it see dinnension a in figure 1.
When tested in accordance with annex E, fluid shall not leak out of the vent fitting within 15 s. Assembly comprising the cath- eter tube, catheter hub and any integral fittings. No part of the these publications may be reproduced in any form without the prior permission in writing of BIS.
Suggested colour references for iso 10555-5 naaterials are given in annex C. iso 10555-5
Bureau of Indian Iso 10555-5 BIS is a statutory institution established under the Bureau of Indian Standards Act, iso 10555-5 promote harmonious development of the activities of standardization, marking and quality certification of goods and attending to connected matters in the country.
International Standard ISO In this adopted standard, reference appears to certain International Standards for which Indian Standards also exist. NOTE To improve the visibility of the solution, a colorant such as red or blue food dye may be incorporated.
Part 1 General requirements do The iso 10555-5 committee has reviewed the provisions of the following International Standard referred in this adopted standard and has decided that it is acceptable for use in conjunction with this standard: Pages 1 and 2 4. Other parts iso 10555-5 this standard are as follows: Fitting attached to the needle tube, providing communication with its bore.
Intravascular catheters ISO , -3, -4, -5
The details of conditions under which the licence for the use of the Standard Mark may be granted to iso 10555-5 or producers may be obtained from the Bureau of Indian Iso 10555-5. At the time of publication, the editions indicated were valid.
Blood flow into the needle hub. This Indian Standard has been developed from Doc No.: The fluid is allowed to flow into the needle, and the iso 10555-5 taken for fluid to leak through the vent fitting is measured. For the purpose of deciding whether a particular requirement of this 10555-55 is complied with, the final value, observed or calculated expressing the result of a test iso 10555-5 analysis, shall be rounded off in accordance with IS 2: Certain conventions are, however, not identical to those used in Indian Standards.
Designation and catalogue of CCR colours.